437-003-0005 | Apply the other divisions of the Oregon code to equipment, processes and practices that are not construction-specific | 0 |
437-003-0015 | Provide potable drinking water in covered, clean containers refilled daily | 0 |
437-003-0020 | Provide flush toilets and washing facilities on projects of one million dollars or more, and keep toilets clean | 0 |
437-003-0027 | Apply the general industry occupational noise rule whenever employees are exposed to noise | 0 |
437-003-0047 | Keep out of the restricted space around overhead high voltage lines unless the owner has de-energised and grounded them or barriers prevent contact, after proper notification | 0 |
437-003-0062 | Run a respiratory protection programme for employees who must use respirators for lead | 0 |
437-003-0065 | Fit extension ladders with guide irons, locks and hooks and assemble them with the sliding section on top | 0 |
437-003-0071 | Keep the manufacturer's manual with aerial platforms, follow its instructions, and use personal fall protection on boom-supported platforms | 0 |
437-003-0085 | Keep three feet of horizontal clearance around rotating superstructures or barricade the area, and control pinch points | 0 |
437-003-0094 | Lift personnel on forklifts only from a guarded, secured platform with an attending operator and controlled descent and travel | 0 |
437-003-0096 | Locate underground utilities under the Oregon one-call law before excavating, then protect them while the excavation is open | 0 |
437-003-0134a | Assess workplace hazards, select protective equipment that fits each employee, and keep all equipment sanitary and reliable | 0 |
437-003-0134b | Train employees in protective equipment, pay for it, and require fall protection, suitable work clothing and high-visibility garments | 0 |
437-003-0404 | Protect temporary receptacles with ground-fault circuit interrupters or an assured equipment grounding conductor programme | 0 |
437-003-0420 | Control traffic on and beside roadways with devices, flaggers and barricades that conform to the MUTCD | 0 |
437-003-0502 | Rig personal fall restraint so the user cannot fall, with conforming components and independent anchorages | 0 |
437-003-0503 | Train every employee exposed to fall hazards, certify the training in writing and retrain when needed | 0 |
437-003-0706 | Establish limited access zones at masonry walls and brace walls over eight feet until permanently supported | 0 |
437-003-0752 | Develop, sign and keep on site a written site-specific steel erection plan with the required contents | 0 |
437-003-0753 | Use tag lines to control hoisted loads unless a qualified rigger finds they create a hazard | 0 |
437-003-0761 | Certify steel erection training in writing, keep the latest record and retrain when understanding lapses | 0 |
437-003-0905 | Lay under-flooring or floor the tier below as wood-framed structures rise | 0 |
437-003-0910 | Make temporary floors strong enough for the expected loading | 0 |
437-003-0915 | Brace or guy structures during erection, alteration or repair and keep the bracing until the structure is secured | 0 |
437-003-0920 | Provide certified shoring and bracing plans when Oregon OSHA requires them | 0 |
437-003-0925 | Use powder-actuated tools that meet the national standard for powder-actuated fastening systems | 0 |
437-003-1000 | Limit employee exposure to air contaminants to the Oregon ceiling, time-weighted average and excursion limits and prevent skin exposure | 0 |
437-003-1101 | Run a respiratory protection programme for employees who must use respirators for asbestos, never with filtering facepieces | 0 |
437-003-1501 | Provide fall protection at six feet, verify surface strength, cover holes, guard wall openings and protect excavation edges | 0 |
437-003-1502 | Use warning lines only on low-slope roofs and protect employees between the line and the edge | 0 |
437-003-1752 | Keep copies of the steel erection written notifications on site until the project is complete | 0 |
437-003-1754 | Deck over roof and floor holes and openings, or guard them as soon as they are created | 0 |
437-003-2501 | Protect employees from falling objects with hard hats and toeboards, canopies or barricades, and cover holes above them | 0 |
437-003-2502 | Use safety monitoring systems only for low-slope roofing within width limits, with a dedicated competent monitor | 0 |
437-003-3060 | Run a respiratory protection programme for employees who must use respirators for methylenedianiline | 0 |
437-003-3224 | Qualify drivers, bar unsafe vehicles, enforce seating, seatbelts and traffic laws, and control riding in truck beds | 0 |
437-003-3225 | Equip and maintain highway vehicles that employees drive or maintain to the rule's component, warning light, bus and crew truck requirements | 0 |
437-003-3226 | Operate, load, equip and maintain off-highway vehicles safely | 0 |
437-003-3600 | Keep mechanised equipment and loads clear of power lines and treat every overhead wire as energised | 0 |
A | Purpose, Oregon definitions, adoption by reference and general interpretations | 0 |
C-adopted | Maintain the adopted general safety and health programme: inspections, training, first aid, fire, housekeeping, illumination, sanitation, records and egress | 0 |
CC-adopted | Comply with the adopted cranes and derricks in construction requirements | 0 |
D-adopted | Comply with the adopted occupational health controls: medical services, sanitation, radiation, illumination, ventilation, hazard communication, MDA, lead and hazardous waste operat | 0 |
E-adopted | Comply with the adopted electrical protective equipment, respiratory protection and working over water sections | 0 |
F-adopted | Comply with the adopted fire protection and prevention requirements | 0 |
H-adopted | Comply with the adopted materials handling, storage, rigging and waste disposal requirements | 0 |
I-adopted | Comply with the adopted hand and power tool requirements | 0 |
J-adopted | Comply with the adopted welding and cutting requirements | 0 |
K-adopted | Comply with the adopted electrical installation, work practice and maintenance requirements | 0 |
L-adopted | Comply with the adopted scaffolding capacity, construction, access, use, fall protection, aerial lift and training requirements | 0 |
M-adopted | Meet the adopted criteria for guardrail, safety net, personal fall arrest, positioning device and cover systems | 0 |
N-adopted | Comply with the adopted helicopter, hoist, elevator and conveyor requirements | 0 |
O-adopted | Comply with the adopted equipment, material handling equipment, pile driving, site clearing and marine operations requirements | 0 |
P-adopted | Comply with the adopted excavation and protective system requirements | 0 |
Q-adopted | Comply with the adopted concrete and masonry construction requirements | 0 |
R-adopted | Comply with the adopted steel erection site layout, hoisting, assembly, anchorage, joist, metal building, falling object and fall protection requirements | 0 |
S-adopted | Comply with the adopted underground construction, caisson, cofferdam and compressed air requirements | 0 |
T-adopted | Comply with the adopted demolition requirements | 0 |
U-adopted | Comply with the adopted blasting and explosives requirements | 0 |
W-adopted | Comply with the adopted rollover protective structure and overhead protection requirements | 0 |
X-adopted | Comply with the adopted stairway and ladder requirements and train ladder and stairway users | 0 |
Z-adopted | Comply with the adopted asbestos, chromium (VI), cadmium and methylene chloride standards | 0 |