International (IEC SC 65A); adopted as EN 61508 / BS EN 61508:2010 and nationally

IEC 61508:2010

84 controls. 2 other frameworks in our corpus share controls with it. Here is all of it, and how much of it you are already doing.

Page built . This page is derived from the framework corpus, which changes when the corpus is extended rather than daily.

84 controls 2 frameworks share controls with it International (IEC SC 65A); adopted as EN 61508 / BS EN 61508:2010 and nationally verified against its source document

Every control below is one this framework asks for. The right hand column counts how many other frameworks in our corpus carry the same control, which is the difference between doing this work once and doing it again for the next standard.

There is no implementation kit for this framework yet. The control list and the overlap above are free and complete.

What you already have

Frameworks whose controls overlap this one, most first. If you run any of them, the count is roughly what you have already evidenced.

Every control

CodeControlAlso in
1-1Part 1, 1 Scope0
1-4Part 1, 4 Conformance to this standard0
1-5.2Part 1, 5.2 Documentation requirements1
1-6.2Part 1, 6.2 Management of functional safety: requirements2
1-7.1.4Part 1, 7.1.4 Overall safety lifecycle: requirements1
1-7.10.2Part 1, 7.10.2 system safety requirements spec (SRS): requirements1
1-7.11Part 1, 7.11 E/E/PE safety-related systems: realisation0
1-7.12Part 1, 7.12 Other risk reduction measures: specification and realisation0
1-7.13.2Part 1, 7.13.2 Overall installation and commissioning: requirements0
1-7.14.2Part 1, 7.14.2 Overall safety validation: requirements1
1-7.15.2Part 1, 7.15.2 Overall operation, maintenance and repair: requirements1
1-7.16.2Part 1, 7.16.2 Overall modification and retrofit: requirements1
1-7.17.2Part 1, 7.17.2 Decommissioning or disposal: requirements1
1-7.18.2Part 1, 7.18.2 Verification: requirements1
1-7.2.2Part 1, 7.2.2 Concept: requirements1
1-7.3.2Part 1, 7.3.2 Overall scope definition: requirements1
1-7.4.2Part 1, 7.4.2 Hazard and risk analysis: requirements1
1-7.5.2Part 1, 7.5.2 Overall safety requirements: requirements1
1-7.6.2Part 1, 7.6.2 Overall safety requirements allocation: requirements1
1-7.7.2Part 1, 7.7.2 Overall operation and maintenance planning: requirements1
1-7.8.2Part 1, 7.8.2 Overall safety validation planning: requirements1
1-7.9.2Part 1, 7.9.2 Overall installation and commissioning planning: requirements0
1-8.2Part 1, 8.2 Functional safety assessment: requirements2
1-ANNEXESPart 1, informative annexes A to G0
2-7.1.3Part 2, 7.1.3 E/E/PE lifecycle: requirements1
2-7.2.2Part 2, 7.2.2 design requirements spec (DRS): requirements1
2-7.2.3Part 2, 7.2.3 design requirements spec (DRS): content1
2-7.3.2Part 2, 7.3.2 E/E/PE validation planning: requirements1
2-7.4.10Part 2, 7.4.10 Requirements for proven in use elements1
2-7.4.11Part 2, 7.4.11 Additional requirements for data communications0
2-7.4.2Part 2, 7.4.2 E/E/PE system design and development: general requirements1
2-7.4.3Part 2, 7.4.3 Synthesis of elements to achieve the required systematic capability1
2-7.4.4.1Part 2, 7.4.4.1 Hardware safety integrity architectural constraints: general requirements1
2-7.4.4.2Part 2, 7.4.4.2 Route 1H1
2-7.4.4.3Part 2, 7.4.4.3 Route 2H1
2-7.4.5Part 2, 7.4.5 Requirements for quantifying the effect of random hardware failures1
2-7.4.6Part 2, 7.4.6 Requirements for the avoidance of systematic faults1
2-7.4.7Part 2, 7.4.7 Requirements for the control of systematic faults1
2-7.4.8Part 2, 7.4.8 Requirements for system behaviour on detection of a fault1
2-7.4.9Part 2, 7.4.9 Requirements for E/E/PE system implementation1
2-7.5.2Part 2, 7.5.2 E/E/PE system integration: requirements1
2-7.6.2Part 2, 7.6.2 E/E/PE system operation and maintenance procedures: requirements1
2-7.7.2Part 2, 7.7.2 E/E/PE validation: requirements1
2-7.8.2Part 2, 7.8.2 E/E/PE system modification: requirements1
2-7.9.2Part 2, 7.9.2 E/E/PE system verification: requirements1
2-APart 2, Annex A (normative) Techniques and measures to control failures during operation1
2-BPart 2, Annex B (normative) Techniques and measures to avoid systematic failures in the lifecycle phases1
2-CPart 2, Annex C (normative) Diagnostic coverage and safe failure fraction1
2-DPart 2, Annex D (normative) Safety manual for compliant items1
2-EPart 2, Annex E (normative) Special architecture requirements for ICs with on-chip redundancy1
2-FPart 2, Annex F (informative) Techniques and measures for ASICs0
3-6.2Part 3, 6.2 Additional requirements for management of safety-related software2
3-7.1.2Part 3, 7.1.2 Software safety lifecycle: requirements2
3-7.2.2Part 3, 7.2.2 Software safety requirements specification: requirements2
3-7.3.2Part 3, 7.3.2 Validation plan for software aspects of system safety: requirements2
3-7.4.2Part 3, 7.4.2 Software design and development: general requirements2
3-7.4.3Part 3, 7.4.3 Requirements for software architecture design2
3-7.4.4Part 3, 7.4.4 Requirements for support tools, including programming languages2
3-7.4.5Part 3, 7.4.5 Requirements for detailed design and development: software system design2
3-7.4.6Part 3, 7.4.6 Requirements for code implementation2
3-7.4.7Part 3, 7.4.7 Requirements for software module testing2
3-7.4.8Part 3, 7.4.8 Requirements for software integration testing2
3-7.5.2Part 3, 7.5.2 Programmable electronics integration (hardware and software): requirements2
3-7.7.2Part 3, 7.7.2 Software aspects of system safety validation: requirements2
3-7.8.2Part 3, 7.8.2 Software modification: requirements2
3-7.9.2Part 3, 7.9.2 Software verification: requirements2
3-8Part 3, 8 Functional safety assessment of software2
3-A.1Part 3, Annex A Table A.1 Software safety requirements specification techniques2
3-A.10Part 3, Annex A Table A.10 Functional safety assessment techniques0
3-A.2Part 3, Annex A Table A.2 Software architecture design techniques2
3-A.3Part 3, Annex A Table A.3 Support tools and programming language techniques2
3-A.4Part 3, Annex A Table A.4 Detailed design techniques2
3-A.5Part 3, Annex A Table A.5 Software module testing and integration techniques2
3-A.6Part 3, Annex A Table A.6 Programmable electronics integration techniques2
3-A.7Part 3, Annex A Table A.7 Software aspects of system safety validation techniques2
3-A.8Part 3, Annex A Table A.8 Modification techniques2
3-A.9Part 3, Annex A Table A.9 Software verification techniques2
3-ANNEXESPart 3, informative annexes B, C, E, F and G0
3-DPart 3, Annex D (normative) Safety manual for compliant items: software elements2
P4Part 4: Definitions and abbreviations0
P5Part 5: Examples of methods for the determination of safety integrity levels (informative)0
P6Part 6: Guidelines on the application of Parts 2 and 3 (informative)0
P7Part 7: Overview of techniques and measures (informative)0
STANDARDIEC 61508:2010: the series and its status0

Tell me when IEC 61508:2010 files something new

One email when a public company newly discloses something this framework governs, naming the company and what our corpus says it puts in scope. Nothing else, and one click to stop.

What this page is

A control-level reference for IEC 61508:2010, drawn from our framework corpus. Control codes and titles are references to the standard, not reproductions of it. The overlap counts and the auditor artefacts are our own work and are the part you will not find elsewhere.

Measure this against what you already run · All frameworks · Today's edition