Australia

Australian Dangerous Goods Code Edition 7.8 (Consignor and Transport Duties)

60 controls. 0 other frameworks in our corpus share controls with it. Here is all of it, and how much of it you are already doing.

Page built . This page is derived from the framework corpus, which changes when the corpus is extended rather than daily.

60 controls 0 frameworks share controls with it Australia verified against its source document

Every control below is one this framework asks for. The right hand column counts how many other frameworks in our corpus carry the same control, which is the difference between doing this work once and doing it again for the next standard.

There is no implementation kit for this framework yet. The control list and the overlap above are free and complete.

What you already have

Frameworks whose controls overlap this one, most first. If you run any of them, the count is roughly what you have already evidenced.

No measured overlap with another framework in the corpus.

Every control

CodeControlAlso in
10.2.1.1Position vehicles carrying flammable gases or liquids to drive away forward during transfer0
10.2.1.2-10.2.1.4Restrictions on transfers in public areas, designated areas and enclosed spaces0
10.2.1.5Protect hose assemblies from vehicles during transfer0
10.2.2.1-10.2.2.2No ignition sources in the hazardous area and engines stopped during flammable transfers0
10.2.2.3-10.2.2.5Electrical bonding, bottom-contact loading spears and no heaters during transfer0
10.2.3General transfer requirements: vehicle immobilised, operator in attendance with shut-off access, cabin empty, adequate light, inert gas pressure0
10.2.4Gas transfers: LP gas under AS/NZS 1596 and no liquefied gas transfers into receptacles inside buildings0
11.1.1.1The consignor gives the prime contractor the dangerous goods transport information, with a hard copy carried in the vehicle0
11.1.1.2Form of the transport document: any format, dangerous goods listed first, numbered pages, English, legible and durable0
11.1.1.3Consignor and consignee names and addresses, the consignor's contact telephone number and the document date0
11.1.1.4.1The dangerous goods description: UN number, proper shipping name, class, subsidiary hazards, packing group, package types, number and aggregate quantity0
11.1.1.4.2Sequence of the description: identifiers first and in order when written as a string0
11.1.1.4.3Supplement the proper shipping name: technical names, EMPTY UNCLEANED, WASTE, MOLTEN, HOT, STABILIZED and TEMPERATURE CONTROLLED0
11.1.1.5Additional document entries: salvage packagings, control and emergency temperatures, infectious substance contacts, expired tank tests, special provisions and holding time0
11.1.2Show which unit of a combination carries which goods, amend documents after part unloading, and describe goods not subject to the Code0
11.1.3Carry the transport documentation in the cabin, in the emergency information holder for placard loads, readable by the driver0
11.1.4Rail: a train manifest may replace transport documents on stated conditions0
11.2.1Carry emergency information: the ANZ-ERG or emergency procedure guides for the goods and for vehicle fire0
11.2.2Emergency information holder marked in red and mounted on or beside a cabin door0
12.1.1Equip every road vehicle carrying a placard load with extinguishers, three warning devices and the required PPE0
12.1.2Fire extinguishers to Table 12.1: compliant, quick-release mounted, accessible and correctly located0
12.1.3Personal protective and safety equipment to Table 12.2 for every hazard in the load, clean, serviceable and accessible0
13.1.2Breakdowns: hazard or parking lights on and warning triangles placed at the prescribed distances0
13.1.3.1No unauthorised passengers in the cabin0
13.1.3.2Parking: brake applied, not in gear without an anti-start device, and away from public places, crowds, other dangerous goods vehicles and naked flames0
13.1.3.3Unload only to a present consignee or into an agreed secure place0
13.1.3.4Detach trailers containing dangerous goods only at marshalling areas, depots, for immediate exchange, in an emergency or on breakdown0
13.1.3.5Cargo heaters off while moving, except bitumen tankers under AS 2809.50
13.1.4Pre-plan routes to minimise risk, avoid sensitive areas and observe authority restrictions0
2.0.1Assign every substance and article to a class, division and packing group by its predominant hazard0
2.0.2-3.1.2Identify the UN number and proper shipping name from the dangerous goods list0
3.4.1Apply the limited quantity concession only within the listed inner packaging amounts0
4.1.1.1Pack dangerous goods in good quality packagings that withstand transport and are closed as the manufacturer directs0
4.1.1.2Packaging materials in contact with the goods must be compatible0
4.1.1.3Use packagings that conform to a successfully tested design type0
4.1.1.4Leave sufficient ullage when filling liquids0
5.1.2Overpacks: visible marks and labels or repeat them, no incompatible goods, secured packages, orientation and strength0
5.1.3-5.1.4Empty uncleaned packagings stay marked and labelled; mixed packing carries every substance's marks0
5.2.1.1Mark each package with the proper shipping name and UN number at the required size0
5.2.1.1.1Mark the Australian name and address of the manufacturer, consignor or agent0
5.2.1.2-5.2.1.4Marks must be visible, durable, contrasting and not crowded; salvage packagings marked SALVAGE; large packagings marked on two opposing sides0
5.2.1.6Environmentally hazardous substance mark on packages of UN 3077 and UN 30820
5.2.1.7Orientation arrows on packages of liquids, vented packagings and cryogenic receptacles0
5.2.1.9Lithium battery mark on packages prepared under special provision 1880
5.2.2.1.1Label every package, receptacle, IBC, overpack and unpackaged article with the primary and subsidiary hazard labels0
5.2.2.1.2-1.5Select labels from the dangerous goods list columns, the precedence rules and the Class 2 subsidiary table0
5.2.2.1.6Place labels on the same surface as the proper shipping name mark, unobscured and in the specified form0
5.3.1.1.1Placard cargo transport units that carry a placard load, and every bulk container and placardable unit0
5.3.1.1.2Placards match the primary hazard, with the mixed class label allowed for multi-class placard loads0
5.3.6.1Placard road vehicles with a placard load on the front and rear0
5.3.6.2Combination vehicles: front and rear placards for the aggregate load, side placards for each unit with its own placard load0
5.3.6.3Emergency information panels for bulk containers, tanks and placardable units on road vehicles0
5.3.9Remove placards only when freed of dangerous goods, and always once freed0
8.1.2.1-8.1.2.2Load packages only into sound cargo transport units inspected before loading0
8.1.2.3-8.1.2.5Stow and restrain to the Load Restraint Guide, segregate incompatibles, follow loading instructions and protect other goods0
8.1.2.7-8.1.2.9Vented closures uppermost, no harmful atmospheres in the cabin, and no damaged or leaking packages accepted0
9.2.1Do not transport incompatible goods together unless segregated under Chapter 9.20
9.2.2Segregation methods: separate vehicles, wagons or closed freight containers, or an approved packaging for segregation0
P1What the ADG Code is, how it binds and what this framework leaves out0
P2Training and security are regulated outside the Code0

Tell me when Australian Dangerous Goods Code Edition 7.8 (Consignor and Transport Duties) files something new

One email when a public company newly discloses something this framework governs, naming the company and what our corpus says it puts in scope. Nothing else, and one click to stop.

What this page is

A control-level reference for Australian Dangerous Goods Code Edition 7.8 (Consignor and Transport Duties), drawn from our framework corpus. Control codes and titles are references to the standard, not reproductions of it. The overlap counts and the auditor artefacts are our own work and are the part you will not find elsewhere.

Measure this against what you already run · All frameworks · Today's edition