Australia (model for the harmonised WHS jurisdictions: Commonwealth, NSW, Qld, SA, WA, Tas, ACT, NT; not Victoria)

Australia Model Code of Practice: Managing the Risks of Plant in the Workplace

54 controls. 0 other frameworks in our corpus share controls with it. Here is all of it, and how much of it you are already doing.

Page built . This page is derived from the framework corpus, which changes when the corpus is extended rather than daily.

54 controls 0 frameworks share controls with it Australia (model for the harmonised WHS jurisdictions: Commonwealth, NSW, Qld, SA, WA, Tas, ACT, NT; not Victoria) verified against its source document

Every control below is one this framework asks for. The right hand column counts how many other frameworks in our corpus carry the same control, which is the difference between doing this work once and doing it again for the next standard.

There is no implementation kit for this framework yet. The control list and the overlap above are free and complete.

What you already have

Frameworks whose controls overlap this one, most first. If you run any of them, the count is roughly what you have already evidenced.

No measured overlap with another framework in the corpus.

Every control

CodeControlAlso in
1.2a1.2 Eliminate or minimise physical and psychosocial risks from plant (primary duty)0
1.2b1.2 Meet the specific duties of the person with management or control of plant (rr 203 to 213)0
1.2c1.2 Meet upstream duties as designer, manufacturer, importer, supplier or installer0
1.2d1.2 Exercise officer due diligence and make workers and others aware of their duties on plant0
1.3a1.3 Manage plant risk through the systematic process and hierarchy of control0
1.3b1.3 Pass safety information about plant from designer to end user0
1.3c1.3 Consult workers on plant risks and changes0
1.3d1.3 Consult, cooperate and coordinate with other duty holders on shared plant0
1.41.4 Provide plant information, training, instruction and supervision (r 39)0
1.51.5 Register plant designs and items that require registration before supply or use0
2.1a2.1 Identify plant hazards across the whole life of the plant0
2.1b2.1 Identify psychosocial hazards that plant creates and hazards that plant could control0
2.1c2.1 Use plant that is designed to lift or suspend the load, and lift within limits0
2.1dAppendix C: Use the plant hazard checklist0
2.22.2 Assess plant risks by severity, likelihood and exposure where needed0
2.3a2.3 Select plant controls using the hierarchy and check they do not create new hazards0
2.3b2.3 Keep people, plant and things a safe distance from electric lines (r 166)0
2.42.4 Maintain and review plant control measures (rr 37 and 38)0
3.1a3.1 Select suitable plant before purchasing or hiring0
3.1b3.1 Meet supplier duties for second-hand plant and scrap (rr 198 to 200)0
3.1c3.1 Agree responsibilities when hiring or leasing plant0
3.2a3.2 Control risks from installation and commissioning (r 204)0
3.2b3.2 Position plant so it can be used, accessed and escaped safely0
3.3a3.3 Prevent unauthorised alteration and use plant only for its designed purpose (rr 205 and 206)0
3.3b3.3 Lift persons only in a work box and with plant specifically designed where possible (rr 219 and 220)0
3.3c3.3 Check high risk work licences before allowing licensed plant work (r 85)0
3.4a3.4 Reassess risk when the way plant is used changes0
3.4b3.4 Control alterations to plant and register altered designs0
3.53.5 Have a competent person inspect, test and maintain plant (r 213)0
3.63.6 Maintain, repair and clean plant under isolation and controlled restart0
3.73.7 Leave plant not in use in a safe state and recommission after storage (r 207)0
3.8a3.8 Control the risks of powered mobile plant (rr 214 and 215)0
3.8b3.8 Fit and keep operator protective devices on quad bikes0
3.93.9 Decommission, dismantle and dispose of plant safely0
4.1a4.1 Guard plant using the required order of barrier types (r 208)0
4.1b4.1 Design, maintain and refit guards so they work and cannot easily be defeated0
4.1c4.1 Use presence-sensing safeguarding where physical guards are not reasonably practicable0
4.24.2 Provide operational controls that are marked, reachable, protected and lockable (r 210)0
4.34.3 Fit emergency stops that are prominent, red, reachable and not defeated by circuit failure (r 211)0
4.44.4 Fit warning devices that suit the plant and its environment (rr 212 and 215)0
4.54.5 Isolate all energy sources before work on plant using lock-out0
4.64.6 Prevent roll-away of vehicles and mobile plant0
4.74.7 Place, check and remove wheel chocks safely0
5.1a5.1 Register the plant design before supply and verify it0
5.1b5.1 Register altered plant designs (rr 244 and 282)0
5.2a5.2 Register each registrable item of plant and mark it0
5.2b5.2 Renew item registration and notify changes within 14 days0
6.1a6.1 Keep records of registered plant for as long as it is used (r 237)0
6.1b6.1 Keep presence-sensing and good practice plant records0
editionEdition, amendment history and approvals0
glossaryAppendices A, B and D: glossary, registrable plant lists and technical standards0
plant-natureWhat plant is and the harm it can cause (section 1.1)0
scopeScope and application of the code0
statusLegal status: an approved code is admissible evidence, not law0

Tell me when Australia Model Code of Practice: Managing the Risks of Plant in the Workplace files something new

One email when a public company newly discloses something this framework governs, naming the company and what our corpus says it puts in scope. Nothing else, and one click to stop.

What this page is

A control-level reference for Australia Model Code of Practice: Managing the Risks of Plant in the Workplace, drawn from our framework corpus. Control codes and titles are references to the standard, not reproductions of it. The overlap counts and the auditor artefacts are our own work and are the part you will not find elsewhere.

Measure this against what you already run · All frameworks · Today's edition