Australia (model for the harmonised WHS jurisdictions: Commonwealth, NSW, Qld, SA, WA, Tas, ACT, NT; not Victoria)

Australia Model Code of Practice: Managing the Risk of Falls at Workplaces

69 controls. 1 other frameworks in our corpus share controls with it. Here is all of it, and how much of it you are already doing.

Page built . This page is derived from the framework corpus, which changes when the corpus is extended rather than daily.

69 controls 1 frameworks share controls with it Australia (model for the harmonised WHS jurisdictions: Commonwealth, NSW, Qld, SA, WA, Tas, ACT, NT; not Victoria) verified against its source document

Every control below is one this framework asks for. The right hand column counts how many other frameworks in our corpus carry the same control, which is the difference between doing this work once and doing it again for the next standard.

There is no implementation kit for this framework yet. The control list and the overlap above are free and complete.

What you already have

Frameworks whose controls overlap this one, most first. If you run any of them, the count is roughly what you have already evidenced.

If you runShared controls
ISO 45001:201820measure it →

Every control

CodeControlAlso in
1.11.1 Identify every duty holder for fall risks and their overlapping duties1
1.2a1.2 Consult workers who are affected by fall hazards1
1.2b1.2 Consult, cooperate and coordinate with other duty holders on fall risks1
1.3a1.3 Provide information, training, instruction and supervision for work at height1
1.3b1.3 Construction workers hold general construction induction training1
10.110.1 Prevent suspension intolerance and train workers for rescue0
10.210.2 Train for rescues: immediate start, frequency set by competence, no risk to rescuers1
10a10 Establish and test emergency and rescue procedures where fall arrest is used (r 80)1
10b10 Provide first aid equipment, facilities and trained first aiders (r 42)1
2.12.1 Eliminate or minimise fall risks at the design stage1
2.22.2 Design plant so it can be accessed, maintained and cleaned without falls0
2.3a2.3 Buildings and structures: design out work at height and pass on residual risk information0
2.3b2.3 Plan for building maintenance and site layout0
3.13.1 Use risk assessment where it helps decide fall controls1
3.23.2 Identify all fall hazards, including access and exit1
3.33.3 Assess fall risks against the listed factors, and keep generic assessments current1
3.4a3.4 Manage fall risk: work on the ground or a solid construction and provide safe access and exit (r 78)1
3.4b3.4 Minimise remaining fall risk through the ordered controls (r 79)1
3.4c3.4 Combine controls where one is not enough, without creating new hazards1
3.4d3.4 Maintain fall controls through procedures and a planned inspection program (r 37)1
3.4e3.4 Review and revise fall controls when triggered (r 38)1
4.14.1 Do the work on the ground wherever reasonably practicable0
4.2a4.2 Solid construction: load capacity and perimeter barriers0
4.2b4.2 Protect holes, penetrations and openings immediately with secure, marked covers0
4.2c4.2 Keep solid construction surfaces non-slip and within safe gradients; secure grid mesh flooring0
4.2d4.2 Provide safe entry and exit to and around the solid construction0
55 Fall prevention devices: use one where work cannot be on the ground or a solid construction0
5.1a5.1 Scaffolds: completion confirmation, inspections and securing incomplete scaffolds (r 225)0
5.1b5.1 Scaffolds: erection by licensed people, standards, edge protection and worker instruction0
5.1c5.1 Suspended (swing stage) scaffolds0
5.1d5.1 Elevating work platforms: hazards, safe use, harness anchorage and licensing0
5.1e5.1 Mast climbing work platforms: licensed erection and dismantling0
5.1f5.1 Workboxes and work platforms on cranes, hoists and forklifts: general precautions0
5.1g5.1 Crane-suspended workboxes: registered design and safe use0
5.1h5.1 Forklift-supported work platforms0
5.1i5.1 Building maintenance units0
5.1j5.1 Trestle ladder scaffolds: height limits, platform width and safe assembly0
5.2a5.2 Perimeter guardrails at edges, openings and on plant0
5.2b5.2 Guardrails or set-back barriers for trenches0
5.35.3 Roof safety mesh: specification, installation and use with edge protection0
66 Work positioning systems: only after higher controls, with competent and fit users1
6.16.1 Restraint technique: set so the wearer cannot reach an unprotected edge0
6.26.2 Industrial rope access: risk assessment, SWMS, supervision and back-up systems0
77 Fall arrest systems: last in order, correctly selected, rated and installed0
7.17.1 Catch platforms0
7.27.2 Safety nets0
7.3a7.3 Individual fall arrest systems: trained users, helmets, post-fall certification and marking0
7.3b7.3 Anchorage points: rated, tested and positioned for connection before exposure0
7.3c7.3 Inspect fall arrest components after installation, periodically and after a fall1
7.3d7.3 Limit free fall and total fall distance; fit harnesses and reels correctly0
7.3e7.3 Use compatible connectors to prevent roll-out0
7.3f7.3 Plan prompt rescue and control swing down and swing back0
7.47.4 Vertical anchorage lines or rails on ladders and towers0
7.57.5 Double lanyards: correct use and limits0
88 Administrative controls: support only, never alone where higher controls are practicable0
8.18.1 No go areas with signs, barriers and supervision0
8.28.2 Permit systems restricting access to trained people0
8.38.3 Organise and sequence work to limit exposure0
99 Use ladders only after safer alternatives are ruled out0
9.1a9.1 Select portable ladders suited to the task and rated for industrial use0
9.1b9.1 Train ladder users; inspect, set up and secure ladders before use0
9.1c9.1 Use ladders safely: three points of contact and the listed prohibitions0
9.1d9.1 Single or extension ladders used for access: secured, extended and protected at the step-off0
9.29.2 Fixed ladders: angle, fall arrest above 75 degrees and rescue in cages0
9.39.3 Inspect and maintain ladders; repair or replace faulty ones1
appendicesAppendices A and B: glossary and references0
approvalsEdition and jurisdictional approvals0
scopeScope and application of the code0
statusLegal status: an approved code is admissible evidence, not law0

Tell me when Australia Model Code of Practice: Managing the Risk of Falls at Workplaces files something new

One email when a public company newly discloses something this framework governs, naming the company and what our corpus says it puts in scope. Nothing else, and one click to stop.

What this page is

A control-level reference for Australia Model Code of Practice: Managing the Risk of Falls at Workplaces, drawn from our framework corpus. Control codes and titles are references to the standard, not reproductions of it. The overlap counts and the auditor artefacts are our own work and are the part you will not find elsewhere.

Measure this against what you already run · All frameworks · Today's edition