Australia (model for the harmonised WHS jurisdictions: Commonwealth, NSW, Qld, SA, WA, Tas, ACT, NT; not Victoria)

Australia Model Code of Practice: How to Manage Work Health and Safety Risks

41 controls. 0 other frameworks in our corpus share controls with it. Here is all of it, and how much of it you are already doing.

Page built . This page is derived from the framework corpus, which changes when the corpus is extended rather than daily.

41 controls 0 frameworks share controls with it Australia (model for the harmonised WHS jurisdictions: Commonwealth, NSW, Qld, SA, WA, Tas, ACT, NT; not Victoria) verified against its source document

Every control below is one this framework asks for. The right hand column counts how many other frameworks in our corpus carry the same control, which is the difference between doing this work once and doing it again for the next standard.

There is no implementation kit for this framework yet. The control list and the overlap above are free and complete.

What you already have

Frameworks whose controls overlap this one, most first. If you run any of them, the count is roughly what you have already evidenced.

No measured overlap with another framework in the corpus.

Every control

CodeControlAlso in
1.1a1.1 The PCBU must eliminate risks, or minimise them so far as reasonably practicable0
1.1b1.1 Officers exercise due diligence over how the PCBU manages risk0
1.1c1.1 Designers, manufacturers, importers, suppliers and installers keep their products free of risk0
1.1d1.1 Workers and other people at the workplace take reasonable care and follow instructions0
1.2a1.2 Show management commitment to health and safety0
1.2b1.2 Work through the four step risk management process in proportion to the business0
1.2c1.2 Apply good work design at the earliest planning stage0
1.2d1.2 Decide what is reasonably practicable by weighing the listed matters0
1.2e1.2 Consult workers and their representatives at each step of the process0
1.2f1.2 Consult, cooperate and coordinate with other duty holders on shared risks0
1.31.3 Run the risk management process whenever circumstances change0
2.02 Identify hazards across the whole of work, physical and psychological0
2.1a2.1 Inspect the workplace and observe how work is actually done0
2.1b2.1 Consult workers on hazards, near misses and unreported incidents0
2.1c2.1 Consult supply chains and networks about hazards0
2.1d2.1 Review available information and analyse records for hazards0
3.03 Assess risks to decide severity, adequacy of controls, action and urgency0
3.1a3.1 Assess risk when uncertainty, interacting hazards or change call for it0
3.1b3.1 Do the risk assessments the Regulations require and measure where exposure standards apply0
3.1c3.1 Know when a detailed assessment is not needed and when a past one can be reused0
3.2a3.2 Work out how each hazard could cause harm as a chain of events0
3.2b3.2 Estimate how severe the harm could be0
3.2c3.2 Estimate how likely harm is to occur0
4.04 Control risks: eliminate or minimise, after consulting affected workers0
4.1a4.1 Work down the hierarchy of control measures0
4.1b4.1 Eliminate the hazard first, ideally at design or planning0
4.1c4.1 Substitute, isolate or apply engineering controls where elimination is not practicable0
4.1d4.1 Use administrative controls only for the risk that remains0
4.1e4.1 Provide suitable PPE as the last layer and train people to use it0
4.2a4.2 Source control information and develop specific controls from the chain of events0
4.2b4.2 Choose controls that are the highest available, suitable and do not create new hazards0
4.2c4.2 Weigh cost properly, never as a reason to do nothing0
4.2d4.2 Implement controls with procedures, training, supervision and maintenance0
4.34.3 Keep controls effective over time0
5a5 Review controls on the triggers the Regulations set0
5b5 Use the review questions and set review frequency by level of risk0
66 Keep records of the risk management process0
appendicesAppendices A to D: glossary, examples, chain of events and risk register0
approvalsEdition: November 2024, current0
scopeScope and application of the code0
statusLegal status: an approved code is admissible evidence, not law0

Tell me when Australia Model Code of Practice: How to Manage Work Health and Safety Risks files something new

One email when a public company newly discloses something this framework governs, naming the company and what our corpus says it puts in scope. Nothing else, and one click to stop.

What this page is

A control-level reference for Australia Model Code of Practice: How to Manage Work Health and Safety Risks, drawn from our framework corpus. Control codes and titles are references to the standard, not reproductions of it. The overlap counts and the auditor artefacts are our own work and are the part you will not find elsewhere.

Measure this against what you already run · All frameworks · Today's edition