Australia (model for the harmonised WHS jurisdictions: Commonwealth, NSW, Qld, SA, WA, Tas, ACT, NT; not Victoria)

Australia Model Code of Practice: Hazardous Manual Tasks

48 controls. 0 other frameworks in our corpus share controls with it. Here is all of it, and how much of it you are already doing.

Page built . This page is derived from the framework corpus, which changes when the corpus is extended rather than daily.

48 controls 0 frameworks share controls with it Australia (model for the harmonised WHS jurisdictions: Commonwealth, NSW, Qld, SA, WA, Tas, ACT, NT; not Victoria) verified against its source document

Every control below is one this framework asks for. The right hand column counts how many other frameworks in our corpus carry the same control, which is the difference between doing this work once and doing it again for the next standard.

There is no implementation kit for this framework yet. The control list and the overlap above are free and complete.

What you already have

Frameworks whose controls overlap this one, most first. If you run any of them, the count is roughly what you have already evidenced.

No measured overlap with another framework in the corpus.

Every control

CodeControlAlso in
1.3a1.3 Eliminate or minimise hazardous manual task risks (primary duty)0
1.3b1.3 Duty holders upstream: design, manufacture, import, supply and installation0
1.3c1.3 Exercise officer due diligence and make worker and visitor duties known0
1.4a1.4 Manage musculoskeletal risk through the regulated risk management steps (r 60)0
1.4b1.4 Consult workers and health and safety representatives at each step0
1.4c1.4 Consult, cooperate and coordinate with other duty holders on shared handling tasks0
1.4d1.4 Provide information, training, instruction and supervision, including on PPE (r 39)0
2.1a2.1 Consult workers to find hard, tiring or uncomfortable tasks0
2.1b2.1 Review records, look for trends and observe how tasks are really done0
2.2a2.2 Recognise force as a hazard: repetitive, sustained, high and sudden0
2.2b2.2 Recognise repetitive movement, and sustained or awkward posture0
2.2c2.2 Recognise whole-body and hand-arm vibration0
3.13.1 Carry out a risk assessment for hazardous tasks unless the risk and control are known0
3.2a3.2 Run the assessment with the right people, by task stage, with specialist help when needed0
3.2b3.2 Group similar tasks only when they are truly similar and review when uncertain0
3.3a3.3 Test for repetitive movement, sustained or awkward postures and repetitive or sustained force0
3.3b3.3 Test for high or sudden force0
3.3c3.3 Test for exposure to vibration, and take the combined result0
3.4a3.4 Find the sources of risk in work area design and layout, loads and tools0
3.4b3.4 Find the sources of risk in systems of work and individual factors0
3.4c3.4 Find the sources of risk in the work environment0
4.14.1 Have regard to all contributing matters and apply the hierarchy of control (r 60(2))0
4.24.2 Purchase equipment that reduces manual task risk0
4.3a4.3 Design workstations and working heights to keep postures neutral0
4.3b4.3 Provide for varied working positions and adequate work space0
4.4a4.4 Reduce risk when handling loads and choose and maintain hand tools0
4.4b4.4 Provide mechanical aids that are suited, maintained and supported by training0
4.4c4.4 Reduce the effort of pushing and pulling loads0
4.4d4.4 Control the risk of handling people0
4.4e4.4 Control the risk of handling animals0
4.5a4.5 Set workload and pace of work the body can sustain0
4.5b4.5 Design tasks for the working population and provide resources and support0
4.6a4.6 Control whole-body and hand-arm vibration0
4.6b4.6 Control cold, heat, humidity and wind in manual task areas0
4.6c4.6 Keep floors clear and provide suitable lighting0
4.7a4.7 Use job rotation and rest breaks as supporting administrative controls0
4.7b4.7 Use team handling only as a temporary or rare measure and plan it0
4.8a4.8 Implement controls with interim measures, worker input and a trial period0
4.8b4.8 Run a manual task training program and keep records0
55 Maintain and review controls for musculoskeletal risk (r 38)0
6.1a6.1 Design plant and structures to eliminate or minimise hazardous manual tasks (r 61)0
6.1b6.1 Design workplaces and plant with the building and plant lifecycle in mind0
6.26.2 Manufacture, import and supply plant and goods with handling in mind (r 61)0
appendicesAppendices A to G: glossary, design examples, process summary, worksheets and assessment tools0
editionEdition, amendment history and approvals0
msdWhat a musculoskeletal disorder and a hazardous manual task are (sections 1.1 and 1.2)0
scopeScope and application of the code0
statusLegal status: an approved code is admissible evidence, not law0

Tell me when Australia Model Code of Practice: Hazardous Manual Tasks files something new

One email when a public company newly discloses something this framework governs, naming the company and what our corpus says it puts in scope. Nothing else, and one click to stop.

What this page is

A control-level reference for Australia Model Code of Practice: Hazardous Manual Tasks, drawn from our framework corpus. Control codes and titles are references to the standard, not reproductions of it. The overlap counts and the auditor artefacts are our own work and are the part you will not find elsewhere.

Measure this against what you already run · All frameworks · Today's edition