Australia (model for the harmonised WHS jurisdictions: Commonwealth, NSW, Qld, SA, WA, Tas, ACT, NT; not Victoria)

Australia Model Code of Practice: Excavation Work

111 controls. 0 other frameworks in our corpus share controls with it. Here is all of it, and how much of it you are already doing.

Page built . This page is derived from the framework corpus, which changes when the corpus is extended rather than daily.

111 controls 0 frameworks share controls with it Australia (model for the harmonised WHS jurisdictions: Commonwealth, NSW, Qld, SA, WA, Tas, ACT, NT; not Victoria) verified against its source document

Every control below is one this framework asks for. The right hand column counts how many other frameworks in our corpus carry the same control, which is the difference between doing this work once and doing it again for the next standard.

There is no implementation kit for this framework yet. The control list and the overlap above are free and complete.

What you already have

Frameworks whose controls overlap this one, most first. If you run any of them, the count is roughly what you have already evidenced.

No measured overlap with another framework in the corpus.

Every control

CodeControlAlso in
1.11.1 Treat excavation work as construction work and identify high risk construction work0
1.2a1.2 PCBU primary duty of care for excavation work (WHS Act s 19)0
1.2b1.2 Principal contractor duties for a construction project (WHS Regulations 293, 308 to 315)0
1.2c1.2 Duties of designers, manufacturers, importers, suppliers and installers (WHS Act ss 22 to 26)0
1.2d1.2 Officers must exercise due diligence (WHS Act s 27)0
1.2e1.2 Duties of workers (WHS Act ss 7, 28; WHS Regulation 46)0
1.2f1.2 Duties of other persons at the workplace (WHS Act s 29)0
1.3a1.3 Apply the systematic risk management process (WHS Regulations 34 to 38)0
1.3b1.3 Manage the specific excavation risks before work starts (WHS Regulation 305)0
1.3c1.3 Consult workers on excavation health and safety (WHS Act ss 47 to 49)0
1.3d1.3 Consult, cooperate and coordinate with other duty holders (WHS Act s 46)0
1.4a1.4 Provide suitable information, training, instruction and supervision (WHS Act s 19; WHS Regulation 39)0
1.4b1.4 Site-specific training, plant licences and competent supervisors (WHS Regulation 317)0
2.12.1 Identify all hazards of the excavation work0
2.2a2.2 Assess the risks where the risk or its control is not well known0
2.2b2.2 Review available information, records and incidents0
2.3a2.3 Work through the hierarchy of control measures0
2.3b2.3 Combine control measures without creating new hazards0
2.42.4 Maintain and review control measures (WHS Regulation 38)0
33 Plan excavation work before it starts, in consultation0
3.1a3.1 Principal contractor duties on a construction project (WHS Regulations 292, 293)0
3.1b3.1 Excavation contractor appointed principal contractor for site preparation0
3.2a3.2 Designers must design safely and give a written safety report (WHS Act s 22; WHS Regulation 295)0
3.2b3.2 Person commissioning construction work consults the designer and passes on hazard information0
3.3a3.3 Content of a SWMS for high risk construction work (WHS Regulation 299)0
3.3b3.3 Prepare the SWMS before high risk construction work starts and coordinate who prepares it0
3.3c3.3 Stop work that departs from the SWMS (WHS Regulation 300)0
3.4a3.4 Use appropriately licensed asbestos removalists (WHS Regulations 422, 458)0
3.4b3.4 Identify or assume asbestos before demolition or excavation (WHS Regulations 422, 451)0
3.4c3.4 Obtain and review the asbestos register (WHS Regulations 426, 448 to 450)0
3.4d3.4 Transport and dispose of asbestos waste lawfully0
3.5a3.5 Protect adjacent buildings and structures from collapse0
3.5b3.5 Control vibration and water effects on nearby buildings0
3.6a3.6 Manage risks from essential services at the workplace0
3.6b3.6 Control excavators and earthmoving plant near overhead powerlines0
3.6c3.6 SWMS for work on or near gas mains, chemical, fuel or refrigerant lines and energised electrical installations0
3.6d3.6 Shut off unneeded services and notify the utility0
3.6e3.6 Obtain current underground essential services information before work starts (WHS Regulation 304)0
3.6f3.6 Sources of underground services information: Before You Dig Australia, authorities and property owners0
3.6g3.6 Share underground services plans with those doing the work0
3.6h3.6 Make services information available and keep it (WHS Regulation 304)0
3.6i3.6 Verify service locations by potholing before digging0
3.6j3.6 Use underground locators with trained operators and prepare a SWMS for work involving services0
3.73.7 Secure the trench work area from unauthorised access (WHS Regulation 306)0
3.8a3.8 Prepare, maintain and implement an emergency plan (WHS Regulation 43)0
3.8b3.8 Tailor the emergency plan to the site and align it with the project plan0
3.8c3.8 Review and revise the emergency plan regularly0
4.1a4.1 Keep plant, vehicles and loads out of the zone of influence0
4.1b4.1 Place excavated material away from the edge and manage runoff0
4.1c4.1 Spoil near old services and obstructions, and the angle of repose0
4.2a4.2 Use plant only for its designed purpose and with its safety features (WHS Regulation 206)0
4.2b4.2 Select, operate and maintain plant and equipment for excavation0
4.2c4.2 Control laser hazards on plant and prohibit class 3B and 4 lasers0
4.3a4.3 Select powered mobile plant for the task and use competent or licensed operators0
4.3b4.3 Implement traffic management and a SWMS where powered mobile plant is used0
4.3c4.3 Run earthmoving machinery and haul roads safely near excavations0
4.3d4.3 Manage blind spots with two-way communication between operators and ground workers (WHS Regulation 215)0
4.3e4.3 Prevent collisions and fit warning devices on powered mobile plant (WHS Regulation 215)0
4.3f4.3 Fit and use operator protective devices, including ROPS and FOPS0
4.3g4.3 Keep powered mobile plant back from the excavation edge0
4.3h4.3 Inspect, maintain and test powered mobile plant and keep logbooks0
4.4a4.4 Manage the risk of falls into excavations (WHS Regulation 78)0
4.4b4.4 Fall control measures for excavations, including fall prevention devices0
4.4c4.4 Prepare a SWMS where a person could fall more than 2 metres0
4.5a4.5 Plan the use of explosives: SWMS, competent advice and applicable laws0
4.5b4.5 Licensed shotfirers, blast management plans and notice to the regulator0
4.6a4.6 Control gas and fume build-up and keep combustion engines out of occupied trenches0
4.6b4.6 Design ventilation for excavations and tunnels0
4.6c4.6 Monitor airborne contaminants (WHS Regulation 50)0
4.6d4.6 Other atmospheric controls: pre-start checks, personal monitors, surface observer and rescue readiness0
4.74.7 Manage hazardous manual tasks in manual excavation (WHS Regulation 60)0
5.1a5.1 Secure trenches at least 1.5 metres deep from unauthorised entry (WHS Regulation 306)0
5.1b5.1 Support all sides of trenches at least 1.5 metres deep by shoring, benching or battering (WHS Regulation 306)0
5.1c5.1 Support trenches of any depth where there is a risk of engulfment0
5.1d5.1 Obtain geotechnical advice on trench stability0
5.1e5.1 Written geotechnical engineer advice where trench sides are safe from collapse0
5.1f5.1 Prepare trench areas and trim from outside the trench0
5.2a5.2 Base tunnel design on an adequate engineering investigation0
5.2b5.2 Tunnel design content and the designer's safety report (WHS Regulation 295)0
5.2c5.2 Control tunnelling hazards and support all tunnel excavation0
5.3a5.3 Control access to shafts and get engineering advice on shaft design0
5.3b5.3 Control the hazards of shaft construction0
66 Plan to prevent ground collapse and never enter an unsupported trench deeper than 1.5 m0
6.1a6.1 Assess ground conditions and factors that weaken soil0
6.1b6.1 Choose among the three types of ground collapse control0
6.2a6.2 Keep benched or battered excavations stable and act on changing conditions0
6.2b6.2 Form benches and batters correctly0
6.2c6.2 Design benches and batters by a competent person and limit slopes to 45 degrees unless certified0
6.3a6.3 Use shoring designed by a competent person where benching or battering will not work0
6.3b6.3 Install shoring progressively and never work ahead of it0
6.3c6.3 Design, inspect and maintain hydraulic shoring systems0
6.3d6.3 Steel sheet piling for major or unstable excavations0
6.3e6.3 Steel trench sheeting: manual handling, laceration and noise controls0
6.3f6.3 Timber soldier sets only in stable ground and to the dimensions shown0
6.3g6.3 Closed sheeting and side lacing: rules for workers0
6.3h6.3 Design ground anchors competently and control soil removal above them0
6.46.4 Remove shoring safely, in reverse order, at backfill stage0
6.5a6.5 Use trench shields and boxes designed for the depth and ground0
6.5b6.5 Install, load, maintain, inspect and modify shields and boxes correctly0
6.66.6 Chemical stabilisation of excavation faces0
6.76.7 Inspect excavations and ground support frequently0
App-AAppendix A: Glossary0
App-BAppendix B: References and other information sources0
App-amendAmendments record0
S1-intro1 Introduction: why excavation collapse is so dangerous0
S2-intro2 The risk management process for excavation work0
S4-table4 Controlling risks in excavation work: common hazards and example controls (Table 2)0
S5-intro5 Excavation methods0
X-forewordForeword: what an approved code of practice is and its legal weight0
X-scopeScope and application of the Code0
X-statusStatus of the model Code of Practice: Excavation work0

Tell me when Australia Model Code of Practice: Excavation Work files something new

One email when a public company newly discloses something this framework governs, naming the company and what our corpus says it puts in scope. Nothing else, and one click to stop.

What this page is

A control-level reference for Australia Model Code of Practice: Excavation Work, drawn from our framework corpus. Control codes and titles are references to the standard, not reproductions of it. The overlap counts and the auditor artefacts are our own work and are the part you will not find elsewhere.

Measure this against what you already run · All frameworks · Today's edition