Australia and New Zealand

AS/NZS 3500.1:2021 Plumbing and Drainage

76 controls. 0 other frameworks in our corpus share controls with it. Here is all of it, and how much of it you are already doing.

Page built . This page is derived from the framework corpus, which changes when the corpus is extended rather than daily.

76 controls 0 frameworks share controls with it Australia and New Zealand verified against its source document

Every control below is one this framework asks for. The right hand column counts how many other frameworks in our corpus carry the same control, which is the difference between doing this work once and doing it again for the next standard.

There is no implementation kit for this framework yet. The control list and the overlap above are free and complete.

What you already have

Frameworks whose controls overlap this one, most first. If you run any of them, the count is roughly what you have already evidenced.

No measured overlap with another framework in the corpus.

Every control

CodeControlAlso in
1Section 1 Scope and general (1.1 to 1.8)0
1.61.6 Equivalent pipe sizes0
1010 Treated greywater services0
11.2-11.311.2 and 11.3 Sanitary flushing supply and water closets0
11.411.4 Urinals0
11.511.5 Installation of cisterns0
11.611.6 Flush valves supplied from break tanks0
11.7-11.811.7 and 11.8 Flush pipes, water distribution and pressure ratio valves0
11.911.9 Flush valves connected to the drinking water service0
1212 Pumps0
1313 Water supply to haemodialysis machines0
1414 Property water meters0
1515 Water supply from rainwater tanks0
1616 Multi-unit developments0
17.2-17.317.2 and 17.3 Flushing and hydrostatic testing0
17.4-17.617.4 to 17.6 Cleaning, disinfection and commissioning0
2.22.2 Materials and products fit for purpose0
2.32.3 General limitations on pipes and fittings0
2.42.4 Metallic pipes and fittings0
2.52.5 Plastics pipes and fittings0
2.62.6 Safe-tray materials0
2.72.7 Joints: flanges, seals, brazing alloys, solvent cement and filler rods0
2.82.8 Miscellaneous materials: concrete, mortar, water, timber, coatings, marking tape0
3.23.2 Flow requirements: flow rates, loading units and simultaneous demand0
3.33.3 Pressure requirements0
3.43.4 Velocity requirements0
3.53.5 Pipe size limitations: water service and branch offtakes0
4.24.2 Protection of water supplies0
4.34.3 Cross-connection hazard rating0
4.4.14.4.1 Provision of backflow prevention devices (individual, zone and containment)0
4.4.34.4.3 Hose taps near zone-protected areas0
4.4.54.4.5 Water downstream of a backflow prevention device0
4.4.64.4.6 Commissioning and maintenance program for testable devices0
4.54.5 Suitability of devices for hazards0
4.6.14.6.1 General installation requirements for backflow devices0
4.6.24.6.2 Location, accessibility and drainage of backflow devices0
4.6.34.6.3 Specific installation requirements for testable and non-testable devices0
5.105.10 Depth of cover0
5.115.11 Bedding and backfill0
5.125.12 Installation in contaminated areas0
5.135.13 Corrosive areas0
5.145.14 Pipes in water-charged or filled ground0
5.155.15 Open channels or watercourses0
5.165.16 Private easements0
5.175.17 Dry services0
5.185.18 Protection against freezing0
5.195.19 Identification of piping0
5.25.2 Installation of pipes and fittings by material0
5.205.20 Temperature control devices0
5.215.21 Australian bushfire prone areas0
5.3.25.3.2 Separation from above-ground services0
5.3.35.3.3 Separation from below-ground services0
5.45.4 Isolating valves0
5.55.5 Location of piping: concealed, in chases and ducts, under slabs0
5.65.6 Methods of jointing0
5.75.7 Support and fixing above ground0
5.85.8 Standpipes0
5.95.9 Anchorage below ground: thrust blocks0
6.2-6.36.2 and 6.3 Fire services: materials, products and installation0
6.4-6.56.4 and 6.5 Fire service water storage tanks and identification0
7.2-7.37.2 and 7.3 Irrigation system types and backflow protection0
7.47.4 Irrigation materials0
8.28.2 Purpose of tanks and limitations on use0
8.38.3 Tank design and installation: support, access, placement0
8.48.4 Tank design: corrosion protection, covers and overflows0
8.5-8.68.5 and 8.6 Tank inlet and outlet piping0
8.7-8.88.7 and 8.8 Sludge valves and safe-trays0
8.98.9 Marking of tanks0
9.29.2 Non-drinking water materials, products and meters0
9.39.3 Non-drinking water installation and proximity to other services0
9.49.4 Non-drinking water cross-connection control0
9.59.5 Temporary bypass0
9.6-9.79.6 and 9.7 Identification of non-drinking pipework and outlets0
9.89.8 Testing and commissioning a non-drinking water service0
APPAppendices A to H0
introStatus of AS/NZS 3500.1:2021 and what supersedes it0

Tell me when AS/NZS 3500.1:2021 Plumbing and Drainage files something new

One email when a public company newly discloses something this framework governs, naming the company and what our corpus says it puts in scope. Nothing else, and one click to stop.

What this page is

A control-level reference for AS/NZS 3500.1:2021 Plumbing and Drainage, drawn from our framework corpus. Control codes and titles are references to the standard, not reproductions of it. The overlap counts and the auditor artefacts are our own work and are the part you will not find elsewhere.

Measure this against what you already run · All frameworks · Today's edition