Australia and New Zealand

AS/NZS 3000:2018 Electrical Installations (Wiring Rules)

68 controls. 0 other frameworks in our corpus share controls with it. Here is all of it, and how much of it you are already doing.

Page built . This page is derived from the framework corpus, which changes when the corpus is extended rather than daily.

68 controls 0 frameworks share controls with it Australia and New Zealand verified against its source document

Every control below is one this framework asks for. The right hand column counts how many other frameworks in our corpus carry the same control, which is the difference between doing this work once and doing it again for the next standard.

There is no implementation kit for this framework yet. The control list and the overlap above are free and complete.

What you already have

Frameworks whose controls overlap this one, most first. If you run any of them, the count is roughly what you have already evidenced.

No measured overlap with another framework in the corpus.

Every control

CodeControlAlso in
1.1-1.41.1 to 1.4 Scope, application, referenced documents and definitions0
1.5.11.5.1 Protection against dangers and damage0
1.5.111.5.11 Protection against abnormal voltages0
1.5.12-1.5.141.5.12 to 1.5.14 Spread of fire, mechanical movement and external influences0
1.5.21.5.2 Control and isolation0
1.5.3-1.5.41.5.3 and 1.5.4 Protection against electric shock and basic protection0
1.5.51.5.5 Fault protection0
1.5.61.5.6 Additional protection by RCDs0
1.5.71.5.7 Basic and fault protection by extra-low voltage0
1.5.8-1.5.101.5.8 to 1.5.10 Thermal effects, overcurrent and earth fault currents0
1.61.6 Design of an electrical installation0
1.7.1-1.7.21.7.1 and 1.7.2 Selection and installation of equipment and work practice0
1.7.3-1.7.41.7.3 and 1.7.4 Equipment selection and damp situations0
1.81.8 Verification (inspection and testing)0
1.9.1-1.9.21.9.1 and 1.9.2 Means of compliance: Part 2 and other standards0
1.9.31.9.3 Alterations and repairs0
1.9.41.9.4 Compliance by specific design and installation (Part 1 solution)0
2.10.22.10.2 Switchboard location, access and exits0
2.10.3-2.10.72.10.3 to 2.10.7 Switchboard construction, bars, identification, wiring and fire protection0
2.22.2 Arrangement of the installation: circuits and maximum demand0
2.32.3 Control of the installation: isolation, main switches, emergency and functional switching0
2.42.4 Fault protection0
2.52.5 Protection against overcurrent and switchboard arcing faults0
2.6.22.6.2 Selection of RCDs0
2.6.3-alterations2.6.3.2.4 to 2.6.3.2.6 Home care, alterations, switchboard replacement and repairs0
2.6.3-domestic2.6.3.2.2 RCDs in domestic and residential installations (Australia)0
2.6.3-nondomestic2.6.3.2.3 RCDs in non-domestic installations (Australia)0
2.7-2.82.7 and 2.8 Protection against overvoltage and undervoltage0
2.92.9 Protection against fire hazard due to arcing faults (AFDDs)0
3.1-3.23.1 and 3.2 Wiring systems: general and types0
3.103.10 Enclosure of cables0
3.113.11 Underground wiring systems0
3.12-3.133.12 and 3.13 Aerial wiring and catenary-supported cables0
3.33.3 External influences on wiring systems0
3.4-3.53.4 and 3.5 Current-carrying capacity and conductor size0
3.63.6 Voltage drop0
3.73.7 Electrical connections, joints and installation couplers0
3.83.8 Identification of conductors0
3.93.9 Installation requirements for wiring systems (other than mechanical protection)0
3.9.43.9.4 Protection of wiring against mechanical damage0
4.14.1 Electrical equipment: general, external influences and air extraction0
4.124.12 Electricity converters (UPS, inverters)0
4.13-4.174.13 to 4.17 Motors, transformers, capacitors, liquid dielectric equipment and batteries0
4.184.18 Gas appliances and equipment0
4.19-4.204.19 and 4.20 Air conditioning, heat pumps and lifts0
4.24.2 Protection against thermal effects0
4.34.3 Connection of electrical equipment0
4.44.4 Socket-outlets0
4.54.5 Lighting equipment, lampholders and recessed luminaires0
4.6-4.74.6 and 4.7 Smoke alarms and cooking appliances0
4.84.8 Appliances producing hot water or steam0
4.9-4.114.9 to 4.11 Room heaters, heating cables and duct heaters0
5.1-5.35.1 to 5.3 Earthing system: MEN, functions and parts0
5.4-5.55.4 and 5.5 Earthing of equipment and earthing arrangements0
5.65.6 Equipotential bonding0
5.7-5.85.7 and 5.8 Earth fault-loop impedance and other earthing arrangements0
6.26.2 Baths, showers and other fixed water containers0
6.3-6.46.3 and 6.4 Swimming pools, spa pools and water features0
6.5-6.76.5 to 6.7 Saunas, refrigeration rooms and hosing-down areas0
7.27.2 Safety services0
7.37.3 Electricity generation systems0
7.4-7.57.4 and 7.5 Electrical separation and extra-low voltage installations0
7.6-7.87.6 to 7.8 High voltage, hazardous areas and standards for specific installations0
7.97.9 Supplies for electric vehicles (New Zealand only)0
8.1-8.28.1 and 8.2 Verification: general, periodic and visual inspection0
8.38.3 Testing0
8.48.4 Verification records0
introStatus of AS/NZS 3000:2018 and amendments0

Tell me when AS/NZS 3000:2018 Electrical Installations (Wiring Rules) files something new

One email when a public company newly discloses something this framework governs, naming the company and what our corpus says it puts in scope. Nothing else, and one click to stop.

What this page is

A control-level reference for AS/NZS 3000:2018 Electrical Installations (Wiring Rules), drawn from our framework corpus. Control codes and titles are references to the standard, not reproductions of it. The overlap counts and the auditor artefacts are our own work and are the part you will not find elsewhere.

Measure this against what you already run · All frameworks · Today's edition