Australia and New Zealand

AS/NZS 1891.4:2009 Industrial Fall-Arrest Systems and Devices

29 controls. 0 other frameworks in our corpus share controls with it. Here is all of it, and how much of it you are already doing.

Page built . This page is derived from the framework corpus, which changes when the corpus is extended rather than daily.

29 controls 0 frameworks share controls with it Australia and New Zealand verified against its source document

Every control below is one this framework asks for. The right hand column counts how many other frameworks in our corpus carry the same control, which is the difference between doing this work once and doing it again for the next standard.

There is no implementation kit for this framework yet. The control list and the overlap above are free and complete.

What you already have

Frameworks whose controls overlap this one, most first. If you run any of them, the count is roughly what you have already evidenced.

No measured overlap with another framework in the corpus.

Every control

CodeControlAlso in
1.21.2 Principles: fall-arrest rated securing, 6 kN maximum arrest force, body support and front attachment0
1.3-1.51.3 to 1.5 Referenced documents, definitions and performance requirements0
1.61.6 Hierarchy of control and hazard-based selection0
2.1.12.1.1 System and equipment selection: investigation before purchase0
2.1.22.1.2 Effects on the wearer: full-body harness and 6 kN maximum force0
2.1.32.1.3 Compatibility of components and systems0
2.1.4-2.1.52.1.4 and 2.1.5 Adverse environments and hazardous work tasks0
2.1.62.1.6 Rescue and first aid planning0
2.2.12.2.1 General requirements for safe use of fall-arrest equipment0
2.2.112.2.11 Training, competency and records0
2.2.2-2.2.42.2.2 to 2.2.4 Pendulum effect, falls over sharp edges and fragile surfaces0
2.2.52.2.5 Restraint technique0
2.2.62.2.6 Working on slopes and work positioning0
2.2.8-2.2.102.2.8 to 2.2.10 Degradation, labels and signs, and equipment combinations0
2.32.3 Fall protection on moveable platforms (building maintenance units, swing stages, boom EWPs)0
3.1.13.1.1 Anchorage selection and strength (Table 3.1)0
3.1.23.1.2 Single-point anchorages for direct connection of personal equipment0
3.23.2 Safe use of anchorages, including diversion anchorages and anchorage signage0
4.14.1 Designation and selection of harnesses0
4.24.2 Designation and selection of lanyards, pole straps and related equipment0
4.34.3 Safe use of harness, lanyard and pole strap systems0
55.1 and 5.2 Fall-arrest devices: designation, selection and safe use0
66.1 to 6.3 Horizontal lifelines and rails: types, selection and safe use0
7-87 and 8 Fall clearance and free-fall distance0
9.1-9.39.1 to 9.3 Inspection: operator inspection and regular scheduled periodic inspection0
9.4-9.69.4 to 9.6 Inspection on entry or re-entry into service, after a fall or defect, and life-expired equipment0
9.7-9.109.7 to 9.10 Ropes and slings, storage and transport, maintenance and equipment records0
APPInformative Appendices A to F0
introStatus, edition and scope of AS/NZS 1891.4:20090

Tell me when AS/NZS 1891.4:2009 Industrial Fall-Arrest Systems and Devices files something new

One email when a public company newly discloses something this framework governs, naming the company and what our corpus says it puts in scope. Nothing else, and one click to stop.

What this page is

A control-level reference for AS/NZS 1891.4:2009 Industrial Fall-Arrest Systems and Devices, drawn from our framework corpus. Control codes and titles are references to the standard, not reproductions of it. The overlap counts and the auditor artefacts are our own work and are the part you will not find elsewhere.

Measure this against what you already run · All frameworks · Today's edition