1.1 | 1.1 Scope | 0 |
1.2 | 1.2 Normative references | 0 |
1.3 | 1.3 Terms and definitions | 0 |
2.1.1 | 2.1.1 Design principles: retaining water in the Category 1 area | 0 |
2.1.2 | 2.1.2 Material selection: compatibility and resistance to movement and exposure | 0 |
2.2.1 | 2.2.1 Enclosed showers: screen prevents water spreading | 0 |
2.2.2 | 2.2.2 Unenclosed showers: Type 1 and Type 2 classification | 0 |
2.3.1 | 2.3.1 Falls in the substrate under the membrane | 0 |
2.3.2 | 2.3.2 Falls in shower floor finishes (Category 1) | 0 |
2.3.3 | 2.3.3 Falls in Category 2 floors next to a shower where a floor waste is fitted | 0 |
2.3.4 | 2.3.4 Category 3 floors without a floor waste | 0 |
2.3.5 | 2.3.5 Whole bathroom designed as an unenclosed shower | 0 |
3.2 | 3.2 Compatibility of system components | 0 |
3.3.1 | 3.3.1 Materials deemed waterproof | 0 |
3.3.2 | 3.3.2 Water-resistant substrates for walls and floors | 0 |
3.3.3 | 3.3.3 Water-resistant surface materials | 0 |
3.4 | 3.4 Preformed and prefinished shower bases and enclosures | 0 |
3.5 | 3.5 Sealants | 0 |
3.6 | 3.6 Fastenings for substrate sheet linings | 0 |
3.7 | 3.7 Adhesives | 0 |
4.10 | 4.10 Fillets and bond breakers for bonded membranes | 0 |
4.11.1 | 4.11.1 Types of junctions, transitions and terminations | 0 |
4.11.2 | 4.11.2 Vertical flashing at shower wall junctions | 0 |
4.12.1 | 4.12.1 Penetrations in shower areas | 0 |
4.12.2 | 4.12.2 Horizontal surface taps at baths and spas | 0 |
4.12.3 | 4.12.3 Other penetrations in Category 1 areas | 0 |
4.12.4 | 4.12.4 Niches, inlaid soap holders and footrests | 0 |
4.13.1 | 4.13.1 Baths and spas: general | 0 |
4.13.2 | 4.13.2 Baths without a shower over them | 0 |
4.13.3 | 4.13.3 Baths with a shower over them | 0 |
4.13.4 | 4.13.4 Freestanding baths | 0 |
4.13.5 | 4.13.5 Bath end walls abutting a shower | 0 |
4.13.6 | 4.13.6 Spa baths | 0 |
4.14 | 4.14 Preformed shower bases | 0 |
4.15 | 4.15 Placement of enclosed shower screens | 0 |
4.16 | 4.16 Vinyl floor and wall coverings | 0 |
4.17 | 4.17 Waterproofing beneath polished concrete | 0 |
4.18 | 4.18 Floor heating | 0 |
4.2 | 4.2 Membrane position relative to tile bed or screed | 0 |
4.3.1 | 4.3.1 Membrane to drainage connection at leak control flanges | 0 |
4.3.2 | 4.3.2 Linear drainage connections | 0 |
4.4.1 | 4.4.1 Surface preparation and substrate falls | 0 |
4.4.3 | 4.4.3 Moisture content of substrates | 0 |
4.4.4 | 4.4.4 Wall sheeting preparation | 0 |
4.4.5 | 4.4.5 Render preparation | 0 |
4.5.1 | 4.5.1 Installing an external membrane | 0 |
4.5.2 | 4.5.2 Curing of membranes | 0 |
4.5.3 | 4.5.3 Membrane inspection before overlay | 0 |
4.5.4 | 4.5.4 Additional membrane continuity testing (when carried out) | 0 |
4.6.1 | 4.6.1 Membrane termination at shower waterstops | 0 |
4.6.2 | 4.6.2 Membrane termination at showers with hobs | 0 |
4.6.3 | 4.6.3 Vertical membrane termination heights | 0 |
4.7 | 4.7 Hob construction | 0 |
4.8.1 | 4.8.1 Waterstops: general | 0 |
4.8.2 | 4.8.2 Waterstops for unenclosed showers | 0 |
4.8.3 | 4.8.3 Waterstops for enclosed showers | 0 |
4.8.4 | 4.8.4 Waterstops for enclosed showers without hobs or set-downs | 0 |
4.8.5 | 4.8.5 Showers within 200 mm of an exit from the wet area | 0 |
4.9.1 | 4.9.1 Perimeter flashing and waterstops at floor-level door openings | 0 |
4.9.2 | 4.9.2 Protecting door frames and architraves | 0 |
APP-A | Appendix A (informative) Design considerations and risk categories | 0 |
APP-B | Appendix B (informative) Falls in floor finishes | 0 |
APP-C | Appendix C (normative) Membrane continuity testing methods | 0 |
APP-DEF | Appendices D, E and F (informative) Checklist, compatibility and moisture testing | 0 |
intro | Status of the Standard | 0 |