Australia

AS 1684.2:2021 Residential Timber-Framed Construction

62 controls. 0 other frameworks in our corpus share controls with it. Here is all of it, and how much of it you are already doing.

Page built . This page is derived from the framework corpus, which changes when the corpus is extended rather than daily.

62 controls 0 frameworks share controls with it Australia verified against its source document

Every control below is one this framework asks for. The right hand column counts how many other frameworks in our corpus carry the same control, which is the difference between doing this work once and doing it again for the next standard.

There is no implementation kit for this framework yet. The control list and the overlap above are free and complete.

What you already have

Frameworks whose controls overlap this one, most first. If you run any of them, the count is roughly what you have already evidenced.

No measured overlap with another framework in the corpus.

Every control

CodeControlAlso in
1.11.1 Scope and application: Class 1 and 10 buildings within the limits, with the Supplements0
1.101.10 Bearing0
1.111.11 Timber: grading and product standards0
1.121.12 Engineered timber and engineered wood products (EWPs)0
1.131.13 Size tolerances0
1.141.14 Alternative timber dimensions0
1.151.15 Steel grade and corrosion protection of connectors0
1.161.16 Requirements for design using the Standard0
1.171.17 Interpolation0
1.181.18 Alternative methods and materials0
1.2-1.31.2 Normative references and 1.3 Terms and definitions0
1.41.4 Limitations: plan, storeys, width, wall height, roof pitch, bracing spacing, roof types and masses0
1.4.21.4.2 Wind classification (N1 to N4)0
1.51.5 Design criteria0
1.61.6 Forces on buildings0
1.71.7 Load paths, offsets and cantilevers0
1.81.8 Durability of structural timber0
1.91.9 Dimensions (member size convention)0
2.3-2.52.3 to 2.5 Nail lamination of members, studs and wall plates0
2.62.6 Load widths and area supported (FLW, CLW, RLW)0
3.23.2 Site preparation and drainage0
3.3-3.43.3 Ground clearance and subfloor ventilation; 3.4 Durability (termites and species)0
3.53.5 Substructure bracing0
3.63.6 Subfloor supports: loads and footing size0
3.73.7 Footings and supports for N1 and N2 (stumps and posts)0
4.14.1 Floor framing general: materials, weatherproofing and shrinkage0
4.1.64.1.6 Cuts, holes and notches in bearers and joists0
4.2.14.2.1 Bearers: building practice0
4.2.24.2.2 Joists: building practice0
4.34.3 Member sizes: bearers and floor joists0
5.2-5.45.2 to 5.4 Platform floors, fitted floors and expansion joints0
5.55.5 Laying and fixing strip and sheet flooring direct to joists0
5.6-5.75.6 Wet area floors and 5.7 joist spacing for flooring0
5.85.8 Decking0
6.2.16.2.1 Studs: crippling, junctions, notches, holes and noggings0
6.2.26.2.2 Plates0
6.2.36.2.3 Openings: lintels, ring beams and jack studs0
6.2.4-6.2.56.2.4 Framing around chimneys and flues; 6.2.5 Lateral support for non-loadbearing walls0
6.3.26.3.2 Wall stud sizes0
6.3.3-6.3.56.3.3 to 6.3.5 Bottom plates, top plates and non-loadbearing wall members0
6.3.66.3.6 Lintels, ring beams and trimmers0
6.3.7-6.3.86.3.7 Verandah beams and 6.3.8 posts supporting roof or floor loads0
7.1.27.1.2 Roof types and limitations (coupled, non-coupled and trussed roofs)0
7.2.1-7.2.47.2.1 to 7.2.4 Ceilings, construction loads, ceiling battens and ceiling joists0
7.2.10-7.2.147.2.10 to 7.2.14 Underpurlins, rafters, ridgeboards, hip and valley rafters and scotch valleys0
7.2.15-7.2.167.2.15 Roof strutting and 7.2.16 collar ties0
7.2.17-7.2.197.2.17 Hip ends, 7.2.18 alternative support systems and 7.2.19 non-coupled roofs0
7.2.207.2.20 Roof battens0
7.2.217.2.21 Trussed roofs0
7.2.22-7.2.277.2.22 to 7.2.27 Roof bracing, fixing to bracing walls, eaves, gables, lateral restraint and chimneys0
7.2.5-7.2.97.2.5 to 7.2.9 Hanging, counter, combined and strutting beams0
7.37.3 Roof and ceiling member sizes0
8.1-8.28.1 Bracing general and 8.2 temporary bracing0
8.3.1-8.3.48.3.1 to 8.3.4 Determining wind pressure, area of elevation and racking force0
8.3.58.3.5 Subfloor bracing0
8.3.68.3.6 Wall bracing: capacity, nominal and structural bracing, distribution and connection0
8.3.78.3.7 Roof bracing0
9.29.2 General connection requirements0
9.4-9.59.4 Nominal and specific fixing requirements and 9.5 nominal (minimum) fixings0
9.69.6 Specific tie-down fixings0
9.79.7 Shear forces (lateral sliding)0
introStatus of the Standard and the series0

Tell me when AS 1684.2:2021 Residential Timber-Framed Construction files something new

One email when a public company newly discloses something this framework governs, naming the company and what our corpus says it puts in scope. Nothing else, and one click to stop.

What this page is

A control-level reference for AS 1684.2:2021 Residential Timber-Framed Construction, drawn from our framework corpus. Control codes and titles are references to the standard, not reproductions of it. The overlap counts and the auditor artefacts are our own work and are the part you will not find elsewhere.

Measure this against what you already run · All frameworks · Today's edition