United States (American National Standard, used internationally)

ANSI/ASIS PAP.1-2012 Physical Asset Protection

97 controls. 5 other frameworks in our corpus share controls with it. Here is all of it, and how much of it you are already doing.

Page built . This page is derived from the framework corpus, which changes when the corpus is extended rather than daily.

97 controls 5 frameworks share controls with it United States (American National Standard, used internationally) verified against its source document

Every control below is one this framework asks for. The right hand column counts how many other frameworks in our corpus carry the same control, which is the difference between doing this work once and doing it again for the next standard.

There is no implementation kit for this framework yet. The control list and the overlap above are free and complete.

What you already have

Frameworks whose controls overlap this one, most first. If you run any of them, the count is roughly what you have already evidenced.

Every control

CodeControlAlso in
55 Leadership and governance0
5.15.1 Top management shows leadership of the physical asset protection programme2
5.25.2 A physical asset protection policy meeting eleven conditions3
66 Establishing the framework0
6.16.1 A PAPMS established, run, maintained and continually improved2
6.26.2 External and internal factors identified, evaluated and taken into account1
6.2.16.2.1 External context defined and documented1
6.2.26.2.2 Internal context defined and documented2
6.2.36.2.3 Risk and resilience management context defined and documented2
6.2.46.2.4 PAPMS scope and boundaries defined and retained2
AAnnex A Guidance on incorporating PAP.1 into the SPC.1-2009 resilience management system0
A.10A.10 Improvement0
A.10.1A.10.1 A documented PAPMS maintenance and change management programme2
A.10.2A.10.2 Continual improvement of the PAPMS2
A.2A.2 Support0
A.2.1A.2.1 Resources for the PAPMS across the PPS life cycle1
A.2.2A.2.2 A formal, documented communication and consultation process2
A.3A.3 PAPMS documentation contents2
A.3.1A.3.1 Records demonstrating conformity and results2
A.3.2A.3.2 Document control procedure with integrity and access protection2
A.4A.4 Planning0
A.4.1A.4.1 Procedures for legal, regulatory and other requirements3
A.4.2A.4.2 A formal, documented risk assessment process kept up to date2
A.4.2.1A.4.2.1 A documented security survey procedure for risk identification and exposure2
A.4.2.2A.4.2.2 A documented risk treatment and countermeasure selection process1
A.5A.5 Objectives, targets and plans to achieve them0
A.5.1A.5.1 PAP objectives and targets2
A.5.2A.5.2 PAP programmes (action plans) to achieve objectives2
A.6A.6 Operation and implementation0
A.6.1A.6.1 Roles, authority, cross-functional teams and command and control2
A.6.2A.6.2 Competence, training and awareness2
A.7A.7 Operational procedures and controls0
A.7.1A.7.1 Countermeasure procedures and a protection in depth strategy2
A.7.2A.7.2 Documented performance criteria and operational control procedures3
A.7.3A.7.3 Design of controls and countermeasures (PPS design)3
A.7.4A.7.4 A PDCA-based physical protection systems life-cycle programme2
A.7.5A.7.5 PPS maintenance, evaluation and replacement2
A.7.6A.7.6 Emergencies, unusual situations and disruptive events4
A.8A.8 Performance evaluation0
A.8.1A.8.1 Monitoring and measurement of PAP performance and PPS effectiveness2
A.8.2A.8.2 Periodic evaluation of compliance2
A.8.3A.8.3 Exercises and testing with formal post-exercise reports2
A.8.4A.8.4 Nonconformities, corrective and preventive action2
A.8.5A.8.5 Internal audit of the PAPMS2
A.9A.9 Management review with defined inputs and outputs2
BAnnex B Informative guidance on the elements of physical asset protection0
B.1B.1 PAP system goals: protection in depth, tolerance of component failure, balanced protection and performance specifications2
B.1.1B.1.1 PAP systems applied through the A.4.2 risk assessment2
B.1.2B.1.2 Security surveys by accredited professionals, with findings followed up1
B.1.3B.1.3 Cost-benefit analysis of controls over the full life cycle1
B.1.4B.1.4 Security convergence of physical and information security risk management1
B.1.5B.1.5 Crime prevention through environmental design (CPTED)2
B.1.5.1B.1.5.1 Implementing CPTED0
B.1.6B.1.6 Site hardening on delay in depth1
B.1.6.1B.1.6.1 Site access control and perimeter delineation1
B.1.6.2B.1.6.2 Implementing site hardening systems2
B.2B.2 Security lighting0
B.2.1B.2.1 Security lighting objectives1
B.2.2B.2.2 Implementing security lighting1
B.3B.3 Barrier systems0
B.3.1B.3.1 Physical barrier systems and their functions1
B.3.2B.3.2 Implementing barrier systems1
B.4B.4 Intrusion detection systems0
B.4.1B.4.1 Intrusion detection objectives1
B.4.2B.4.2 Implementing intrusion detection in concentric layers1
B.5B.5 Physical entry and access control0
B.5.1B.5.1 Entry and access control objectives and the three identification factors1
B.5.2B.5.2 Implementing entry and access control systems1
B.6B.6 Video systems: video surveillance0
B.6.1B.6.1 Defining video system parameters: purpose, retention and image quality1
B.6.10B.6.10 Cost estimate0
B.6.11B.6.11 Procurement and installation1
B.6.12B.6.12 Training of users and administrators1
B.6.13B.6.13 Policies and procedures for system use1
B.6.14B.6.14 Testing: acceptance and periodic checks1
B.6.2B.6.2 Video system architecture1
B.6.3B.6.3 Signal and data transmission1
B.6.4B.6.4 Recording methods0
B.6.5B.6.5 System ownership and division of responsibility1
B.6.6B.6.6 Camera selection by observation category0
B.6.7B.6.7 Direct product comparisons in real placement conditions0
B.6.8B.6.8 Viewing clients and monitoring requirements0
B.6.9B.6.9 Video system design and specification by qualified professionals1
B.7B.7 Alarms, communications and display0
B.7.1B.7.1 Objectives of alarms, communications and display1
B.7.2B.7.2 Implementing alarm monitoring, communications and display0
B.7.2.1B.7.2.1 Security considerations for the command centre1
B.7.2.2B.7.2.2 Technology: network capacity, resilience and space conditioning1
B.7.2.3B.7.2.3 Architectural design of the monitoring facility1
B.7.2.4B.7.2.4 Technical systems: integration and monitoring by exception1
B.8B.8 Personnel: involving people and choosing a security staffing model2
B.9B.9 Security policies and procedures2
FRONTClauses 2 and 3 and Annex C: references and terms0
INTROClause 0: asset protection and the management systems approach0
PRINCIPLESClause 4: the ten general principles of a PAPMS0
STANDARDANSI/ASIS PAP.1-2012: the standard, its scope and how it plugs into a resilience management system0
STATUSEdition status and companions0

Tell me when ANSI/ASIS PAP.1-2012 Physical Asset Protection files something new

One email when a public company newly discloses something this framework governs, naming the company and what our corpus says it puts in scope. Nothing else, and one click to stop.

What this page is

A control-level reference for ANSI/ASIS PAP.1-2012 Physical Asset Protection, drawn from our framework corpus. Control codes and titles are references to the standard, not reproductions of it. The overlap counts and the auditor artefacts are our own work and are the part you will not find elsewhere.

Measure this against what you already run · All frameworks · Today's edition